STO N SHOW

Discussion in 'Canada' started by SRT707HC, Apr 5, 2016.

  1. SRT707HC

    SRT707HC Gold Member Hellcat Car Club

    Joined:
    Jun 25, 2015
    Messages:
    299
    Likes Received:
    176
    Trophy Points:
    293
    Location:
    Mississauga
    Vehicle:
    Challenger SRT Hellcat
    I just installed the sto n show license plate holder... Did not want holes drilled into the bumper.

    Front PLate.jpg
     
    • Like Like x 6
    • Winner Winner x 2
  2. mnf1fan

    mnf1fan Hellcat Member

    Joined:
    Oct 18, 2015
    Messages:
    63
    Likes Received:
    18
    Trophy Points:
    8
    Location:
    MPLS, MN
    Vehicle:
    Challenger SRT Hellcat
    Does it seem like a quality piece?
    That's the same one I'm thinking of getting.
     
  3. goingsolo2

    goingsolo2 Beast will be back bigger and better than ever! Hellcat Car Club Gold Supporting Member Hellcat Supporting Vendor

    Joined:
    Oct 29, 2014
    Messages:
    1,511
    Likes Received:
    578
    Trophy Points:
    313
    Location:
    Long Island, NY
    Vehicle:
    Challenger SRT Hellcat
    Try very hard not to bottom it out on anything. It's a great plate holder...just have to be really careful in steep driveways and over speed bumps.
     
    • Useful Useful x 1
  4. SRT707HC

    SRT707HC Gold Member Hellcat Car Club

    Joined:
    Jun 25, 2015
    Messages:
    299
    Likes Received:
    176
    Trophy Points:
    293
    Location:
    Mississauga
    Vehicle:
    Challenger SRT Hellcat
    It's light weight, but I must say its not 100% sturdy... has a bit of movement to it.
    You will need to make up a bracket for it..
     
  5. SRT707HC

    SRT707HC Gold Member Hellcat Car Club

    Joined:
    Jun 25, 2015
    Messages:
    299
    Likes Received:
    176
    Trophy Points:
    293
    Location:
    Mississauga
    Vehicle:
    Challenger SRT Hellcat
    Stonshow.jpg
     
  6. Booky

    Booky Gold Member

    Joined:
    Feb 6, 2016
    Messages:
    982
    Likes Received:
    615
    Trophy Points:
    638
    Location:
    Van Wert, Ohio
    Vehicle:
    Challenger SRT Hellcat
    Due to the plate sticking down +1" from the splitter with the Sto & Show, I just went this route:

     
    • Like Like x 1
  7. CNYHC

    CNYHC SRT Hellcat Supporter Gold Supporting Member

    Joined:
    May 25, 2015
    Messages:
    1,185
    Likes Received:
    499
    Trophy Points:
    258
    Location:
    Central New York
    Vehicle:
    Challenger SRT Hellcat
    It looks low since I'm parked on my uncut lawn, but I've had no problems with it hitting anything...

    DSCN0990.jpg
     
    • Winner Winner x 3
    • Like Like x 1
  8. Mr Bigblock

    Mr Bigblock Gold Member

    Joined:
    Apr 4, 2015
    Messages:
    725
    Likes Received:
    376
    Trophy Points:
    313
    Location:
    Stoney Creek , Ontario
    Vehicle:
    Challenger SRT Hellcat
    The Sto and Show looks Great but for now I did as above for now but it is not centred coz the Cat has coolers their I installed mine off to the side where their r no Coolers, it comes off easily. DSC_0769.JPG DSC_0772.JPG
     
    • Like Like x 2
    • Winner Winner x 1
  9. SRT707HC

    SRT707HC Gold Member Hellcat Car Club

    Joined:
    Jun 25, 2015
    Messages:
    299
    Likes Received:
    176
    Trophy Points:
    293
    Location:
    Mississauga
    Vehicle:
    Challenger SRT Hellcat
    I should have mentioned, If you decide to go with this set up, I recommend getting a small piece of metal as shown in the picture. It doesn't come with the kit.
     
  10. professor33

    professor33 Hellcat Member

    Joined:
    Aug 11, 2015
    Messages:
    51
    Likes Received:
    15
    Trophy Points:
    8
    Vehicle:
    Challenger SRT Hellcat
    Just installed mine as well... Very nice fit and finish.
    So 3 PCP l's in Ontario so far I see ... Nice
     
  11. Angel

    Angel Gold Member

    Joined:
    Aug 19, 2015
    Messages:
    1,258
    Likes Received:
    567
    Trophy Points:
    313
    Location:
    League City, TX
    Vehicle:
    Challenger SRT Hellcat
    I have this too and so far its been great with no issues so far. No issues with speed bumps and only scraped once on my driveway when I exited at a fairly fast speed which it would have scraped even without it.

    The only thing that worries me with this is if and when I lower my cat. Once lowered I believe it will become an issue.
     
  12. LONGUN

    LONGUN Rookie

    Joined:
    Jun 8, 2015
    Messages:
    9
    Likes Received:
    0
    Trophy Points:
    1
    Vehicle:
    Challenger SRT Hellcat
    Hi. Check out skene design.com. This is what I went with. Item# BKT-1EL. Front plate bracket, US, extra long. Total cost about a year ago $ 56.00
     
  13. Highlyfueled

    Highlyfueled Gold Member

    Joined:
    Sep 12, 2015
    Messages:
    223
    Likes Received:
    125
    Trophy Points:
    293
    Location:
    Florida
    Vehicle:
    Challenger SRT Hellcat
    I'm so glad I live in Florida, you are only required to have a rear plate
     

    Attached Files:

    • Winner Winner x 1
  14. SRT707HC

    SRT707HC Gold Member Hellcat Car Club

    Joined:
    Jun 25, 2015
    Messages:
    299
    Likes Received:
    176
    Trophy Points:
    293
    Location:
    Mississauga
    Vehicle:
    Challenger SRT Hellcat
    I'm in Mississauga
     
  15. Angel

    Angel Gold Member

    Joined:
    Aug 19, 2015
    Messages:
    1,258
    Likes Received:
    567
    Trophy Points:
    313
    Location:
    League City, TX
    Vehicle:
    Challenger SRT Hellcat
    Thanks for sharing this will solve my concerns when I lower my cat.
     

Share This Page

Search tags for this page

challenger hellcat removable front license plate sto and show canada