SRT Hellcat Forum banner

Search results

1-20 of 333 Results
Advanced Search
  1. Steering feels loose front end feels like floating

    SRT Hellcat General Discussions
    Mabye take a look at your cradle mount bushing torque value make sure they are all torqued properly. I noticed that my pass front mount bolt on pass side was finger tite at 3k miles. No more pull to rite and no rear sway after torqued to spec.
  2. Lower Rear Cradle Instructions

    SRT Hellcat General Discussions
    Its nite and day difference in handling very happy with how it worked out for me. 👍
  3. Lower Rear Cradle Instructions

    SRT Hellcat General Discussions
    It's not that bad to do imo, drop your driveshaft unplug exaust valve actuators at actuators pigtail, I dropped whole exaust except headers one bolt holding each tip support strap, loosened clamps at header,spray a little kroil on slip flange remove 2 hanger bolts and wiggle it off from rear...
  4. Black Friday at Beefcake Racing - Over 80 Brands!

    Dodge Charger SRT Hellcat
    Thanks Terry Feel like I got a great deal 👍 James
  5. Help please, Cannot remove caliper tube, did i say please

    SRT Hellcat Maintenance
    Lil penetrating oil, use a center punch on tapered end of pin. Should pop rite out with one or 2 taps
  6. Road Course car setup - what works & what doesn't?

    Road Racing : AutoX : ORR (Open Road Racing)
    Nice...
  7. Service stability control & engine derate?

    SRT Hellcat General Discussions
    Mabye check or clean your rear wheel sensors had a similar issue, cleaned wheel sensors off with some alchohol. Disconnected battery overnite and no codes since. Codes were service traction control, no throttle response,service antilock brake system, and one other but dont remember off hand.
  8. "SOLD" FULL DRAG SET-UP Weld S-71 Beadlocks and Race Star Skinnies

    For Sale: Wheels and Tires
    Recieved in excellent condition, Thankyou
  9. Just bought a 2015 B5 Blue Hellcat 6 MT with 171 original miles!

    New Member Introduction
    Congrats on your Hellcat purchase beautiful looking car man 👍
  10. FI Thermal Blanket

    SRT Hellcat Performance
    I have one, if you can send me a replacement from kirk I would be okay with that
  11. "SOLD" FULL DRAG SET-UP Weld S-71 Beadlocks and Race Star Skinnies

    For Sale: Wheels and Tires
    PM sent
  12. Wrapping Part #6QW33RXFAD for aesthetics

    SRT Hellcat Appearance
    Think I will wrap with Averydennison for new color the cheetah wrap has too many inconsistencies in finish on roll found a few spots in roll. Mabye it was just a bad roll it happens. Anyway this is how it looked for the summer.
  13. Barton and CCI driveshaft issue

    SRT Hellcat Performance
    The only issue I had prior to shim the trans mount was a damaged passenger axle, cars been lowered for couple years with no other issues and no codes. If you decide to remove a little meat from shifter shaft t/o bearing noise should quiet down to normal. Be safe and enjoy bro
  14. Barton and CCI driveshaft issue

    SRT Hellcat Performance
    part of the reason for removing my washers, also had service antilock brake system, service traction control, and believe the other was something about stabilitrac? and no throttle response. Disconnected my battery for 24 hrs pos and neg pulled and cleaned all four wheel sensors and cleaned tone...
  15. Barton and CCI driveshaft issue

    SRT Hellcat Performance
    Good to see they found a solution that will work for your cat. My situation was a little different with setup. James
  16. Livernois Motorsports Upgraded Driveshaft

    Livernois Motorsports
    If you click and expand the pic all of the green gets removed , had to pull nylon bushing inserts because of heat and use a wet towel to keep shaft cool. Tried the trans mount to body shim with washers... that did not work
  17. Wrapping Part #6QW33RXFAD for aesthetics

    SRT Hellcat Appearance
    Appreciate it. Rite at 500.total Appreciate it rite at 500. total cost
  18. Wrapping Part #6QW33RXFAD for aesthetics

    SRT Hellcat Appearance
    progress.... thanks
  19. APR Splitter question

    SRT Hellcat Appearance
    You will need to pull bumper to install APR rods properly it's a functional piece IE downforce
  20. Barton and CCI driveshaft issue

    SRT Hellcat Performance
    visial reference works perfect now no washers under trans mount. 5 min with a grinder and emory cloth to clean up the edges
1-20 of 333 Results
Top