SRT Hellcat Forum banner
  • Hey Everyone! Vote for the Site Favourite HOTM winner for the year of 2022 HERE!

Discussions Showcase Albums Media Media Comments Tags Marketplace

21-34 of 37 Results
  1. For Sale
    Selling the Stock Supercharger Snout from my 2017 Challenger Hellcat. $750. METCO Hub was installed and used with a 3.10" on a 93 Octane Tune done by Curt. Stock Pulley is available and for sale as well. Changed to 3.10" around 1500 miles. $150. Stock Injectors are available and for sale as...
  2. For Sale
    2.75 Metco Pulley (ring and hub). I decided to go with a 2.79 instead. $150 shipped OBO
  3. For Sale
    I recently sold my 2016 Dodge Challenger Hellcat M6 and returned it to its factory condition beforehand. Therefore, I have my parts for sale if you’re interested. THE BELOW WAS PURCHASED FROM HHP AT ONCE (08/18): ---very low miles--- *Diablo Sport Trinity T2 EX SOLD *Metco 2.86 Upper Pulley...
  4. Dodge Charger SRT Hellcat
    Hey everybody! First post! I wish I had a better post to start with, but unfortunately I don't. What I have is a dead HC, no warranty coverage and I have now been labeled a criminal mod-er by Dodge. Yes, I made the mistake of listening to my salesman and I am now paying the price. I can go...
  5. Dodge Challenger SRT Hellcat
    Hey guys So I'm upgrading the injectors and pulley. I'm going with Litens for sure but was hoping to see if someone can give any additional information or insight regarding the pros/cons of going with either the 2.85 vs the 2.72 size. I understand the concept and all, I was just looking to see...
  6. Dodge Charger SRT Hellcat
    Hello, I am a long time Mopar fan and am beginning the process of upgrading my 2016 Hellcat Charger with a 2.75 Metco pulley, QTP electric cut off pipes, and a legmaker intake. I had several questions before installing these and trying to find out what else i need to run this properly. 1. Do I...
  7. Western States
    Any one know of where a good shop to tune and install some parts are in Socal? Looking to do some work on my Hellcat and my buddy is wanting to do some to his T/A. Any advice is needed.
  8. SRT Hellcat Performance
    Is anyone here runs 2.85 from Litens? If so, what are the numbers?
  9. Dodge Charger SRT Hellcat
    Big question I need some expert opinions/ answers on. CAN YOU RUN A 2.85 UPPER PULLEY WITH STOCK INJECTORS? Itll just be a 2.85 pulley, Tune and a CAI (JLT) Is it safe? Saw someone say their friend shot a rod through the motor
  10. SRT Hellcat General Discussions
    Hi - I'm torquing the lower pulley bolt on my 6.2 with an automatic. I removed the inspection plate on the bell housing, I'm considering using a pry bar or large blade against flexplate teeth and the passenger side of the opening, but its thin-wall aluminum casting / engine block. I'm afraid...
  11. Dodge Charger SRT Hellcat
    I've been going back and forth between springing for a CF drive shaft or going with aluminum -- and for the moment I'm leaning toward aluminum. I've read here that the DSS aluminum shaft has (or at least *had,* at one point in time) some issues with losing grease. The Gforce is a little bit...
  12. SRT Hellcat Performance
    Hello everyone, :cool: Ordered new go faster parts from hhp. Pcm, Trinity, tune, 2.85 pulley, kn filter, Gates belt, 180 thermostat and pulley tools. Excited to install but I am not sure of torq requirements for s/c lid and new pulley torq lbs. Can anyone point me in a direction to find these...
  13. SRT Hellcat Performance
    Just wondering if any of youhave had this problem. I installed thebwoody idler pulley and it started squeaking. It has now gotten progressively worse and its almost as loud as the intake now! Any ideas on how to make this irritating noise go away?!?!
21-34 of 37 Results