[hpindy]

Not the strongest rods
But will do. And yes getting parts have been a pita

I don't plan on making a million horsepower. I just want strengthen up what I have now . My car is 99% street car and I'm not into changing pulleys all the time . These will work perfectly for what I have in mind .

Sent from my BBF100-2 using Tapatalk

 

[h8trmkr]

Here’s your Molar rods

 

[hpindy]

Here’s your Molar rods
View attachment 565805

What's the full story behind this ? These rods are more then adaquet for what I'm doing . This is not my first rodeo .

Sent from my BBF100-2 using Tapatalk

 

[h8trmkr]

What's the full story behind this ? These rods are more then adaquet for what I'm doing . This is not my first rodeo .

Sent from my BBF100-2 using Tapatalk

900 wheel horse car tuned by a very well known shop. China parts that’s the problem

 

[hpindy]

I will get pictures as I receive parts . But here is an update .
Molnar PWR rods
Custom diamond pistons with PTFE coated
Custom total seal rings
Coated bearings ( rod and main )
Arp main studs
Custom balanced
This is what I have ordered so far.

Sent from my BBF100-2 using Tapatalk

 

[hpindy]

I just found out my pistons showed up at my buddies house in Michigan! So I should have them home next week ! I have all the gaskets and bearings now too . And my ARP studs are ready for pick up locally.

Sent from my BBF100-2 using Tapatalk

 

[h8trmkr]

I just found out my pistons showed up at my buddies house in Michigan! So I should have them home next week ! I have all the gaskets and bearings now too . And my ARP studs are ready for pick up locally.

Sent from my BBF100-2 using Tapatalk

I HAS ONE SET SHOW UP TUESDAY and my 426 set should be today

 

[hpindy]

I HAS ONE SET SHOW UP TUESDAY and my 426 set should be today

It's like Christmas for car guys

Sent from my BBF100-2 using Tapatalk

 

[h8trmkr]

It's like Christmas for car guys

Sent from my BBF100-2 using Tapatalk

still lots of stuff on BO i want to take the first week of feb off to build my engine and finish my car. than last week go to texas and test

 

[hpindy]

still lots of stuff on BO i want to take the first week of feb off to build my engine and finish my car. than last week go to texas and test

I hear ya . Im still waiting for some miscellaneous parts also that are on BO . I'm not going to pull the engine till March .

Sent from my BBF100-2 using Tapatalk

 

[h8trmkr]

I hear ya . Im still waiting for some miscellaneous parts also that are on BO . I'm not going to pull the engine till March .

Sent from my BBF100-2 using Tapatalk

i have a list
crank
valve springs
supercharger
converter
head gaskets
rims
tires

 

[h8trmkr]

Left 426 piston right 376

 

[hpindy]

Left 426 piston right 376 View attachment 567123 View attachment 567124 View attachment 567125 View attachment 567126 View attachment 567127 View attachment 567128 View attachment 567129

Thanks for the pics . They really show the comparison.
That wrist pin is really up there on the 426 piston . What is the finally compression ratio of the 426?

Sent from my BBF100-2 using Tapatalk

 

[h8trmkr]

Thanks for the pics . They really show the comparison.
That wrist pin is really up there on the 426 piston . What is the finally compression ratio of the 426?

Sent from my BBF100-2 using Tapatalk

Both 9.5

 

[hpindy]

Both 9.5

What is the bore on both pistons ?

Sent from my BBF100-2 using Tapatalk

 

[h8trmkr]

4.090 and 4.100

 

[Himmelkat]

It'd be epic to sleeve the block and have 3.75x4.31.

 

[hpindy]

You want a 440 eh ! Good choice

@Himmelkat

 

[Himmelkat]

The top ring land is mighty thick and strong, too. You would have no trouble running nitrous on that bambino, I suspect.

 

[hpindy]

Ok more new parts ! I have everything to balance the rotating assembly! The pistons are custom made to my specifications including a custom ring pack and upgraded wrist pins.

Sent from my BBF100-2 using Tapatalk